光トランシーバーに関わる設定要素は、速度とFECですが。ここでは使用している光トランシーバーの型番、シリアル、受信している光レベル等を確認するコマンドを列挙します。
show idprom int giga 0/1
show int transceiver detail
cisco9316D# sh int e1/5 transceiver sprom
Ethernet1/5
transceiver is present
type is QSFP-100G-LR4
name is WAVESPLITTER
part number is WST-QS28-ER4L-C
revision is 40
serial number is C920E80002
nominal bitrate is 25500 MBit/sec
Link length supported for 9/125um fiber is 40 km
cisco id is 17
cisco extended id number is 206
Identifier : 0x11 (QSFP28)
Ext_Identifier :0xce
Connector : 0x07 (LC)
10G Ethernet Compliance Code : 0x80 (Extended Range SMF)
Sonet Compliance Code : 0x0000
Gigabit Ethernet Compliance Code: 0x00 (None)
Encoding : 0x03 (NRZ)
BR_Nominal : 0xff [25500]
Reserved1 : 0x02
Length_9u_1 : 0x28 40 KM
Length_9u_2 : 0x00 0 Meters
Length_50u : 0x00 0 Meters
Length_60u : 0x00 0 Meters
Length_Copper : 0x00 0 Meters
Reserved2 : 0x64
Vendor Name : WAVESPLITTER
Reserved3 : 0x00
Vendor OUI : 0x000f0e
Vendor Part No : WST-QS28-ER4L-C
Vendor Revision : 40
Reserved4 : 0x00d100
Check Code ID : 0x3d (OK)
Options : 0x0407
BR Max : 0xff
BR Min : 0xbe
Vendor Serial No : C920E80002
Date Code : 221024
Diagnostic Monitoring Type : 0x0c
enchancedOptions : 0x08
SFF8472Compliance : 0x67
Check Code EXT : 0x8b (OK)
Vendor Specific ID Data : 0x00000000000000000000000000000000
: 0x00000000000000000000000000000000
N9K-C93180YC-FX(config)# show interface ethernet 1/49 transceiver details
Ethernet1/49
transceiver is present
type is QSFP-100G-CWDM4-MSA-FEC
name is WAVESPLITTER
part number is WST-QS28-CM4-C
revision is 61
serial number is CB23W40068
nominal bitrate is 25500 MBit/sec per channel
Link length supported for 9/125um fiber is 2 km
cisco id is 17
cisco extended id number is 204
Lane Number:1 Network Lane
SFP Detail Diagnostics Information (internal calibration)
----------------------------------------------------------------------------
Current Alarms Warnings
Measurement High Low High Low
----------------------------------------------------------------------------
Temperature 32.00 C 75.00 C -5.00 C 70.00 C 0.00 C
Voltage 3.23 V 3.59 V 3.07 V 3.47 V 3.09 V
Current 36.63 mA 90.00 mA 5.00 mA 80.00 mA 10.00 mA
Tx Power -0.45 dBm 2.49 dBm -4.50 dBm 1.99 dBm -4.00 dBm
Rx Power -0.99 dBm 2.49 dBm -11.61 dBm 1.99 dBm -10.60 dBm
Transmit Fault Count = 0
----------------------------------------------------------------------------
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning
Lane Number:2 Network Lane
SFP Detail Diagnostics Information (internal calibration)
----------------------------------------------------------------------------
Current Alarms Warnings
Measurement High Low High Low
----------------------------------------------------------------------------
Temperature 32.00 C 75.00 C -5.00 C 70.00 C 0.00 C
Voltage 3.23 V 3.59 V 3.07 V 3.47 V 3.09 V
Current 37.27 mA 90.00 mA 5.00 mA 80.00 mA 10.00 mA
Tx Power 0.16 dBm 2.49 dBm -4.50 dBm 1.99 dBm -4.00 dBm
Rx Power 0.16 dBm 2.49 dBm -11.61 dBm 1.99 dBm -10.60 dBm
Transmit Fault Count = 0
----------------------------------------------------------------------------
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning
Lane Number:3 Network Lane
SFP Detail Diagnostics Information (internal calibration)
----------------------------------------------------------------------------
Current Alarms Warnings
Measurement High Low High Low
----------------------------------------------------------------------------
Temperature 32.00 C 75.00 C -5.00 C 70.00 C 0.00 C
Voltage 3.23 V 3.59 V 3.07 V 3.47 V 3.09 V
Current 35.20 mA 90.00 mA 5.00 mA 80.00 mA 10.00 mA
Tx Power 0.06 dBm 2.49 dBm -4.50 dBm 1.99 dBm -4.00 dBm
Rx Power -0.54 dBm 2.49 dBm -11.61 dBm 1.99 dBm -10.60 dBm
Transmit Fault Count = 0
----------------------------------------------------------------------------
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning
Lane Number:4 Network Lane
SFP Detail Diagnostics Information (internal calibration)
----------------------------------------------------------------------------
Current Alarms Warnings
Measurement High Low High Low
----------------------------------------------------------------------------
Temperature 32.00 C 75.00 C -5.00 C 70.00 C 0.00 C
Voltage 3.23 V 3.59 V 3.07 V 3.47 V 3.09 V
Current 36.24 mA 90.00 mA 5.00 mA 80.00 mA 10.00 mA
Tx Power -0.43 dBm 2.49 dBm -4.50 dBm 1.99 dBm -4.00 dBm
Rx Power -0.22 dBm 2.49 dBm -11.61 dBm 1.99 dBm -10.60 dBm
Transmit Fault Count = 0
----------------------------------------------------------------------------
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning
cat9500x#show hw-module sub 1/0 transceiver 1 idprom IDPROM for transceiver : Description = QSFP28 optics (type 134) Transceiver Type: = QSFP 100GE SR4 (454) Product Identifier (PID) = QSFP-100G-SR4-S Vendor Revision = 04 Serial Number (SN) = AVF2022G0JG Vendor Name = CISCO-AVAGO Vendor OUI (IEEE company ID) = 00.17.6A (5994) CLEI code = CMUIAL8CAA Cisco part number = 10-3142-01 Device State = Enabled. Date code (yy/mm/dd) = 16/06/02 Connector type = MPO Encoding = 64B66B Nominal bitrate per channel = 25GE (25500 Mbits/s)
cat9500x#show int hun 1/0/2 transceiver detail
show inventory
show controllers fourhundredgige 0/0/0/0
show controllers fourhundredgige 0/0/0/0 internal
show controllers optics 0/0/0/0
mx304> show chassis pic pic-slot 0 fpc-slot 0
FPC slot 0, PIC slot 0 information:
Type MRATE LMIC 16x100G/4x400G
State Online
PIC version 0.0
Uptime 10 days, 11 hours, 9 minutes, 31 seconds
PIC port information:
Fiber Xcvr vendor Wave- Xcvr JNPR MSA
Port Cable type type Xcvr vendor part number length Firmware Rev Version
0 400GBASE-FR4 SM JUNIPER-1F1 740-085349 1301 nm 186.52 REV 01 CMIS 3.0
6 400GBASE-FR4 SM WAVESPLITTER WST-QD4-FR4-C 1301 nm 3.4 XXXX CMIS 4.0nm
mx304> show interfaces diagnostics optics et-0/0/6
Physical interface: et-0/0/6
Module temperature : 58 degrees C / 137 degrees F
Module voltage : 3.2720 V
Module temperature high alarm : Off
Module temperature low alarm : Off
Module temperature high warning : Off
Module temperature low warning : Off
Module voltage high alarm : Off
Module voltage low alarm : Off
Module voltage high warning : Off
Module voltage low warning : Off
Module temperature high alarm threshold : 75 degrees C / 167 degrees F
Module temperature low alarm threshold : -5 degrees C / 23 degrees F
Module temperature high warning threshold : 70 degrees C / 158 degrees F
Module temperature low warning threshold : 0 degrees C / 32 degrees F
Module voltage high alarm threshold : 3.6300 V
Module voltage low alarm threshold : 2.9700 V
Module voltage high warning threshold : 3.4640 V
Module voltage low warning threshold : 3.1340 V
Laser bias current high alarm threshold : 100.000 mA
Laser bias current low alarm threshold : 25.000 mA
Laser bias current high warning threshold : 90.000 mA
Laser bias current low warning threshold : 35.000 mA
Laser output power high alarm threshold : 3.4674 mW / 5.40 dBm
Laser output power low alarm threshold : 0.2399 mW / -6.20 dBm
Laser output power high warning threshold : 2.7542 mW / 4.40 dBm
Laser output power low warning threshold : 0.4786 mW / -3.20 dBm
Laser rx power high alarm threshold : 3.4674 mW / 5.40 dBm
Laser rx power low alarm threshold : 0.0955 mW / -10.20 dBm
Laser rx power high warning threshold : 2.7542 mW / 4.40 dBm
Laser rx power low warning threshold : 0.1905 mW / -7.20 dBm
Laser temperature high alarm threshold : 75 degrees C / 167 degrees F
Laser temperature low alarm threshold : -5 degrees C / 23 degrees F
Laser temperature high warning threshold : 70 degrees C / 158 degrees F
Laser temperature low warning threshold : 0 degrees C / 32 degrees F
Lane 0
Laser bias current : 58.000 mA
Laser output power : 1.667 mW / 2.22 dBm
Laser receiver power : 1.863 mW / 2.70 dBm
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser receiver power high alarm : Off
Laser receiver power low alarm : Off
Laser receiver power high warning : Off
Laser receiver power low warning : Off
Tx loss of signal functionality alarm : Off
Rx loss of signal alarm : Off
Tx laser disabled alarm : Off
Lane 1
Laser bias current : 52.000 mA
Laser output power : 1.697 mW / 2.30 dBm
Laser receiver power : 1.784 mW / 2.51 dBm
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser receiver power high alarm : Off
Laser receiver power low alarm : Off
Laser receiver power high warning : Off
Laser receiver power low warning : Off
Tx loss of signal functionality alarm : Off
Rx loss of signal alarm : Off
Tx laser disabled alarm : Off
Lane 2
Laser bias current : 50.000 mA
Laser output power : 1.650 mW / 2.18 dBm
Laser receiver power : 1.835 mW / 2.64 dBm
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser receiver power high alarm : Off
Laser receiver power low alarm : Off
Laser receiver power high warning : Off
Laser receiver power low warning : Off
Tx loss of signal functionality alarm : Off
Rx loss of signal alarm : Off
Tx laser disabled alarm : Off
Lane 3
Laser bias current : 50.000 mA
Laser output power : 1.651 mW / 2.18 dBm
Laser receiver power : 1.911 mW / 2.81 dBm
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser receiver power high alarm : Off
Laser receiver power low alarm : Off
Laser receiver power high warning : Off
Laser receiver power low warning : Off
Tx loss of signal functionality alarm : Off
Rx loss of signal alarm : Off
Tx laser disabled alarm : Off
> show chassis hardware
Hardware inventory:
Item Version Part number Serial number Description
Chassis xxxxxxxxxxxx JNP7100-32C [ACX7100-32C]
PSM 0 REV 05 740-085431 1ED7C484330 PSU 1600W AC, Front to Back Airflow
PSM 1 REV 05 740-085431 1ED7C484306 PSU 1600W AC, Front to Back Airflow
Routing Engine 0 REV 10 611-112446 YY3623010213 RE-JNP-7100
CB 0 REV 16 650-113148 YX3623010039 Control Board
FPC 0 BUILTIN BUILTIN ACX7100-32C
PIC 0 BUILTIN BUILTIN MRATE- 32xQSFP-DD + 4xQSFP56-DD
Xcvr 0 REV 01 740-058732 1GCQA3480MN QSFP-100GBASE-LR4
Xcvr 2 REV 02 740-054050 1FCPB514049 QSFP+-4X10G-LR
Xcvr 32 REV 01 740-085349 1W2CZBA73100L QSFP56-DD-400G-FR4
Xcvr 33 REV 01 740-131169 2E1CZGA742029 QSFP56-DD-400G-ZR-M
Xcvr 34 XXXX NON-JNPR TH33F20001 QSFP56-DD-400GBASE-DR4
Xcvr 35 REV 01 740-085349 1W1CZBA519004 QSFP56-DD-400G-FR4
> show interfaces diagnostics optics et-0/0/34
Physical interface: et-0/0/34
Module temperature : 39 degrees C / 102 degrees F
Module voltage : 3.198 V
Module temperature high alarm : Off
Module temperature low alarm : Off
Module temperature high warning : Off
Module temperature low warning : Off
Module voltage high alarm : Off
Module voltage low alarm : Off
Module voltage high warning : Off
Module voltage low warning : Off
Module temperature high alarm threshold : 95 degrees C / 203 degrees F
Module temperature low alarm threshold : -20 degrees C / -4 degrees F
Module temperature high warning threshold : 85 degrees C / 185 degrees F
Module temperature low warning threshold : -10 degrees C / 14 degrees F
Module voltage high alarm threshold : 3.63 V
Module voltage low alarm threshold : 2.97 V
Module voltage high warning threshold : 3.549 V
Module voltage low warning threshold : 3.049 V
Laser bias current high alarm threshold : 100 mA
Laser bias current low alarm threshold : 0.5 mA
Laser bias current high warning threshold : 80 mA
Laser bias current low warning threshold : 1 mA
Laser output power high alarm threshold : 5.011 mW / 7.00 dBm
Laser output power low alarm threshold : 0.256 mW / -5.90 dBm
Laser output power high warning threshold : 3.981 mW / 6.00 dBm
Laser output power low warning threshold : 0.323 mW / -4.89 dBm
Laser rx power high alarm threshold : 6.309 mW / 8.00 dBm
Laser rx power low alarm threshold : 0.081 mW / -10.89 dBm
Laser rx power high warning threshold : 5.011 mW / 7.00 dBm
Laser rx power low warning threshold : 0.102 mW / -9.90 dBm
Laser temperature high alarm threshold : 95 degrees C / 203 degrees F
Laser temperature low alarm threshold : -20 degrees C / -4 degrees F
Laser temperature high warning threshold : 85 degrees C / 185 degrees F
Laser temperature low warning threshold : -10 degrees C / 14 degrees F
Lane 0
Laser bias current : 32.381 mA
Laser output power : 1.57 mW / 1.96 dBm
Laser temperature : 39 degrees C / 102 degrees F
Laser receiver power : 0 mW / -40.00 dBm
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser temperature high alarm : Off
Laser temperature low alarm : Off
Laser temperature high warning : Off
Laser temperature low warning : Off
Laser receiver power high alarm : Off
Laser receiver power low alarm : On
Laser receiver power high warning : Off
Laser receiver power low warning : On
Laser output power high alarm : Off
Laser output power low alarm : Off
Laser output power high warning : Off
Laser output power low warning : Off
Tx loss of signal functionality alarm : Off
Rx loss of signal alarm : On
Tx laser disabled alarm : Off
Lane 1
Laser bias current : 31.224 mA
Laser output power : 1.777 mW / 2.49 dBm
Laser temperature : 39 degrees C / 102 degrees F
Laser receiver power : 0 mW / -40.00 dBm
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser temperature high alarm : Off
Laser temperature low alarm : Off
Laser temperature high warning : Off
Laser temperature low warning : Off
Laser receiver power high alarm : Off
Laser receiver power low alarm : On
Laser receiver power high warning : Off
Laser receiver power low warning : On
Laser output power high alarm : Off
Laser output power low alarm : Off
Laser output power high warning : Off
Laser output power low warning : Off
Tx loss of signal functionality alarm : Off
Rx loss of signal alarm : On
Tx laser disabled alarm : Off
Lane 2
Laser bias current : 31.224 mA
Laser output power : 1.691 mW / 2.28 dBm
Laser temperature : 39 degrees C / 102 degrees F
Laser receiver power : 0 mW / -40.00 dBm
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser temperature high alarm : Off
Laser temperature low alarm : Off
Laser temperature high warning : Off
Laser temperature low warning : Off
Laser receiver power high alarm : Off
Laser receiver power low alarm : On
Laser receiver power high warning : Off
Laser receiver power low warning : On
Laser output power high alarm : Off
Laser output power low alarm : Off
Laser output power high warning : Off
Laser output power low warning : Off
Tx loss of signal functionality alarm : Off
Rx loss of signal alarm : On
Tx laser disabled alarm : Off
Lane 3
Laser bias current : 31.224 mA
Laser output power : 1.873 mW / 2.72 dBm
Laser temperature : 39 degrees C / 102 degrees F
Laser receiver power : 0 mW / -40.00 dBm
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser temperature high alarm : Off
Laser temperature low alarm : Off
Laser temperature high warning : Off
Laser temperature low warning : Off
Laser receiver power high alarm : Off
Laser receiver power low alarm : On
Laser receiver power high warning : Off
Laser receiver power low warning : On
Laser output power high alarm : Off
Laser output power low alarm : Off
Laser output power high warning : Off
Laser output power low warning : Off
Tx loss of signal functionality alarm : Off
Rx loss of signal alarm : On
Tx laser disabled alarm : Off
> show interfaces diagnostics optics-profile et-0/0/34
Physical interface: et-0/0/34
Optics type : QSFP-DD
Number of lanes : 4
Power class : class 6 (4.5 W max)
Power mode : high
Host side FEC : not supported
Media side FEC : not supported
Rx output manual control support : no
Tx CDR implemented : no
Rx CDR implemented : no
Tx input equalization type : not supported
Rx output emphasis manual control support : no
Rx output amplitude 100-400 mV no equalization : yes
Rx output amplitude 300-600 mV no equalization : yes
Rx output amplitude 400-800 mV no equalization : yes
Rx output amplitude 600-1200 mV no equalization : yes
Tx squelch manual control support : no
Rx squelch manual control support : no
Tx rate select version : not supported
Rx rate select version : not supported
Lane 0
Tx laser : enabled
Rx output : enabled
Rx output emphasis : 5 dB
Rx output amplitude : 600-1200 mV
Tx squelch : enabled
Rx squelch : enabled
Lane 1
Tx laser : enabled
Rx output : enabled
Rx output emphasis : 5 dB
Rx output amplitude : 600-1200 mV
Tx squelch : enabled
Rx squelch : enabled
Lane 2
Tx laser : enabled
Rx output : enabled
Rx output emphasis : 5 dB
Rx output amplitude : 600-1200 mV
Tx squelch : enabled
Rx squelch : enabled
Lane 3
Tx laser : enabled
Rx output : enabled
Rx output emphasis : 5 dB
Rx output amplitude : 600-1200 mV
Tx squelch : enabled
Rx squelch : enabled
qfx5220> show chassis hardware extensive
show chassis pic fpc-slot 0 pic-slot 0
show interfaces diagnostics optics
> show chassis pic fpc-slot 0 pic-slot 0
> show chassis hardware detail
> show interfaces diagnostics optics
> show interfaces diagnostics optics-applications
admin@sonic:~$ show interface transceiver eeprom Ethernet48 -d
Ethernet48: SFP EEPROM detected
Application Advertisement: N/A
Connector: LC
DOM Capability:
Rx_power_support: no
Temp_support: no
Tx_power_support: no
Voltage_support: no
Encoding: 64B66B
Extended Identifier: Power Class 4(3.5W max), CDR present in Rx Tx
Extended RateSelect Compliance: QSFP+ Rate Select Version 1
Identifier: QSFP28 or later
Length Cable Assembly(m): 0
Nominal Bit Rate(100Mbs): 255
Specification compliance:
Vendor Date Code(YYYY-MM-DD Lot): 2019-07-30
Vendor Name: FINISAR CORP.
Vendor OUI: 00-90-65
Vendor PN: FTLC1151RDPL2
Vendor Rev: A0
Vendor SN: U24A99K
ChannelMonitorValues:
RX1Power: -40.0dBm
RX2Power: -40.0dBm
RX3Power: -40.0dBm
RX4Power: -40.0dBm
TX1Bias: 44.062mA
TX2Bias: 42.818mA
TX3Bias: 42.968mA
TX4Bias: 42.556mA
ChannelThresholdValues:
RxPowerHighAlarm : 5.5dBm
RxPowerHighWarning: 4.5dBm
RxPowerLowAlarm : -14.5967dBm
RxPowerLowWarning : -10.5998dBm
TxBiasHighAlarm : 55.0mA
TxBiasHighWarning : 50.0mA
TxBiasLowAlarm : 25.0mA
TxBiasLowWarning : 30.0mA
ModuleMonitorValues:
Temperature: 26.9766C
Vcc: 3.2212Volts
ModuleThresholdValues:
TempHighAlarm : 65.0C
TempHighWarning: 60.0C
TempLowAlarm : 10.0C
TempLowWarning : 15.0C
VccHighAlarm : 3.63Volts
VccHighWarning : 3.465Volts
VccLowAlarm : 2.97Volts
VccLowWarning : 3.135Volts
ne8000>disp int 100ge0/1/48 ex
100GE0/1/48 current state : UP (ifindex: 54)
Line protocol current state : DOWN
Link quality grade : GOOD
Description: hg-0-0-0-3
Route Port,The Maximum Transmit Unit is 1500
Internet protocol processing : disabled
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is c8b6-d3c1-a4f6
Factor/Module: QSFP28, Standard: 100GBASE-LR4, FecMode: Disable
The Vendor PN is TRQ5E20ENF-LF420
The Vendor Name is Oclaro Inc.
Port BW: 100G, Transceiver max BW: 100G, Transceiver Mode: SingleMode
Connector Type: LC, Transmission Distance: 10km
WaveLength: 1295.56nm 1300.05nm 1304.58nm 1309.14nm
Rx Warning range: [-10.604, 4.499]dBm, Tx Warning range: [-4.300, 4.499]dBm
Rx0 Power: -0.25dBm, Tx0 Power: 1.53dBm
Rx1 Power: -0.19dBm, Tx1 Power: 1.46dBm
Rx2 Power: 0.23dBm, Tx2 Power: 1.48dBm
Rx3 Power: 0.47dBm, Tx3 Power: 1.49dBm
Loopback: none, LAN full-duplex mode, Pause Flowcontrol: Receive Enable and Send Enable
Last physical up time : 2022-06-04 12:59:46
Last physical down time : 2022-06-04 04:31:25
Current system time: 2022-06-06 08:17:41
Statistics last cleared:never
Last 300 seconds input rate: 100134 bits/sec, 7 packets/sec
Last 300 seconds output rate: 6633 bits/sec, 7 packets/sec
Input peak rate 1526309 bits/sec, Record time: 2022-06-06 06:44:23
Output peak rate 67450 bits/sec, Record time: 2022-06-06 06:44:23
Input: 1495190372 bytes, 333621 packets
Output: 34427866 bytes, 322726 packets
Input:
Unicast: 163425 packets, Multicast: 170196 packets
Broadcast: 0 packets, JumboOctets: 189795 packets
CRC: 0 packets, Symbol: 0 packets
Overrun: 0 packets, InRangeLength: 0 packets
LongPacket: 0 packets, Jabber: 0 packets, Alignment: 0 packets
Fragment: 0 packets, Undersized Frame: 0 packets
RxPause: 0 packets
Output:
Unicast: 145312 packets, Multicast: 177414 packets
Broadcast: 0 packets, JumboOctets: 1 packets
Lost: 0 packets, Overflow: 0 packets, Underrun: 0 packets
System: 0 packets, Overruns: 0 packets
TxPause: 0 packets
Local fault: normal, Remote fault: normal.
Last 300 seconds input utility rate: 0.01%
Last 300 seconds output utility rate: 0.01%
Qos car:
Ingress discard packets: 0 packets
Egress discard packets: 0 packets
Port-queue:
Egress discard packets: 0 packets
Arp vlan car:
Ingress discard packets: 0 packets
Port packets:
Receive packets equal to 64 bytes: 307 packets
Receive packets 65~127 bytes: 93609 packets
Receive packets 128~255 bytes: 16705 packets
Receive packets 256~511 bytes: 17071 packets
Receive packets 512~1023 bytes: 6148 packets
Receive packets 1024~1518 bytes: 9994 packets
Receive packets more than 1518 bytes: 189796 packets
Send packets equal to 64 bytes: 2185 packets
Send packets 65~127 bytes: 315016 packets
Send packets 128~255 bytes: 42 packets
Send packets 256~511 bytes: 5493 packets
Send packets 512~1023 bytes: 0 packets
Send packets 1024~1518 bytes: 0 packets
Send packets more than 1518 bytes: 1 packets
FEC Error Counter:
FEC 0 error: --
FEC 1 error: --
FEC 0 and 1 type error: --
FEC symbol error: --
FEC uncorrected error: --
FEC error rate: --
<ce6865>display interface 100GE 1/0/8 trans
100GE1/0/8 transceiver information:
-------------------------------------------------------------------
Common information:
Transceiver Type :100GBASE_LR4
Connector Type :LC
Wavelength (nm) :1310
Transfer Distance (m) :10000(9um/125um SMF)
Digital Diagnostic Monitoring :YES
Vendor Name :HUAWEI
Vendor Part Number :02311KNU
Ordering Name :
-------------------------------------------------------------------
Manufacture information:
Manu. Serial Number :033AXV10K3002014
Manufacturing Date :2019-3-23+09:00
Vendor Name :HUAWEI
-------------------------------------------------------------------
Alarm information:
-------------------------------------------------------------------
<ce6865>display interface trans brief
100GE1/0/1 transceiver diagnostic information:
-------------------------------------------------------------------
Temperature (Celsius) :49.52
Voltage (V) :3.28
Bias Current (mA) :43.94|44.13 (Lane0|Lane1)
44.15|44.45 (Lane2|Lane3)
Current RX Power (dBm) :-1.47|-1.41 (Lane0|Lane1)
-0.44|-1.60 (Lane2|Lane3)
Current TX Power (dBm) :-0.30|-0.27 (Lane0|Lane1)
1.09|0.69 (Lane2|Lane3)
-------------------------------------------------------------------
100GE1/0/2 transceiver diagnostic information:
-------------------------------------------------------------------
Temperature (Celsius) :50.38
Voltage (V) :3.31
Bias Current (mA) :44.30|44.17 (Lane0|Lane1)
44.45|44.88 (Lane2|Lane3)
Current RX Power (dBm) :-2.81|-3.46 (Lane0|Lane1)
-6.17|-3.24 (Lane2|Lane3)
Current TX Power (dBm) :-0.46|0.03 (Lane0|Lane1)
0.58|1.30 (Lane2|Lane3)
-------------------------------------------------------------------
100GE1/0/8 transceiver diagnostic information:
-------------------------------------------------------------------
Temperature (Celsius) :42.34
Voltage (V) :3.25
Bias Current (mA) :65.00|73.99 (Lane0|Lane1)
76.99|67.99 (Lane2|Lane3)
Current RX Power (dBm) :0.93|0.64 (Lane0|Lane1)
1.44|0.94 (Lane2|Lane3)
Current TX Power (dBm) :1.72|1.55 (Lane0|Lane1)
1.55|1.65 (Lane2|Lane3)
-------------------------------------------------------------------
<ce6865>display interface 100GE 1/0/8
100GE1/0/8 current state : UP (ifindex: 12)
Line protocol current state : UP
Description:
Switch Port, PVID : 1250, TPID : 8100(Hex), The Maximum Frame Length is 9216
Internet protocol processing : disabled
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 7c1c-f158-4851
Port Mode: COMMON FIBER, Port Split/Aggregate: DISABLE
Speed: 100000, Loopback: NONE
Duplex: FULL, Negotiation: DISABLE
Input Flow-control: DISABLE, Output Flow-control: DISABLE
Mdi: -, Fec: NONE
Last physical up time : 2019-06-05 14:15:43+09:00
Last physical down time : 2019-06-03 20:45:39+09:00
Current system time: 2019-06-05 14:37:38+09:00
Statistics last cleared:never
Last 300 seconds input rate: 348 bits/sec, 0 packets/sec
Last 300 seconds output rate: 2486 bits/sec, 3 packets/sec
Input peak rate 348 bits/sec, Record time: 2019-06-05 14:37:38+09:00
Output peak rate 2714 bits/sec, Record time: 2019-06-05 14:20:29+09:00
Input : 25009 bytes, 140 packets
Output: 450595 bytes, 4904 packets
Input:
Unicast: 0, Multicast: 77
Broadcast: 63, Jumbo: 0
Discard: 0, Frames: 0
Pause: 0
Total Error: 0
CRC: 0, Giants: 0
Jabbers: 0, Fragments: 0
Runts: 0, DropEvents: 0
Alignments: 0, Symbols: 0
Ignoreds: 0
Output:
Unicast: 8, Multicast: 707
Broadcast: 4189, Jumbo: 0
Discard: 0, Buffers Purged: 0
Pause: 0
Input bandwidth utilization threshold : 90.00%
Output bandwidth utilization threshold: 90.00%
Last 300 seconds input utility rate: 0.01%
Last 300 seconds output utility rate: 0.01%
root@SN2410:~# l1-show swp53
Port: swp53
Module Info
Vendor Name: WAVESPLITTER PN: WST-QS28-ER4L-C
Identifier: 0x11 (QSFP28) Type: 100g-er4
Configured State
Admin: Admin Up Speed: 100G MTU: 9216
Autoneg: On FEC: Auto
Operational State
Link Status: Kernel: Up Hardware: Up
Speed: Kernel: 100G Hardware: 100G
Autoneg: On (Autodetect enabld) FEC: RS
TX Power (mW): [1.7025, 2.057, 2.2285, 1.6412]
RX Power (mW): [0.0564, 0.0846, 0.0711, 0.0787]
Topo File Neighbor: None, None
LLDP Neighbor: SN2410, swp55
Port Hardware State:
Compliance Code: 100GBASE-ER4 or 25GBASE-ER
Cable Type: Optical Module (separated)
Speed: 100G Autodetect: Enabled
Eyes: 386, 419, 392, 379 Grade: 23983, 28798, 23983, 23171
Troubleshooting Info: No issue was observed.
Port: swp55
Module Info
Vendor Name: WAVESPLITTER PN: WST-QS28-ER4L-C
Identifier: 0x11 (QSFP28) Type: 100g-er4
Configured State
Admin: Admin Up Speed: 100G MTU: 9216
Autoneg: On FEC: Auto
Operational State
Link Status: Kernel: Up Hardware: Up
Speed: Kernel: 100G Hardware: 100G
Autoneg: On (Autodetect enabld) FEC: RS
TX Power (mW): [1.568, 1.7627, 1.4638, 1.5707]
RX Power (mW): [0.0474, 0.0518, 0.0535, 0.0663]
Topo File Neighbor: None, None
LLDP Neighbor: SN2410, swp53
Port Hardware State:
Compliance Code: 100GBASE-ER4 or 25GBASE-ER
Cable Type: Optical Module (separated)
Speed: 100G Autodetect: Enabled
Eyes: 405, 365, 353, 405 Grade: 22192, 27870, 19860, 23577
Troubleshooting Info: No issue was observed.
root@SN2410:~# ethtool -m swp53
Identifier : 0x11 (QSFP28)
Extended identifier : 0xce
Extended identifier description : 3.5W max. Power consumption
Extended identifier description : CDR present in TX, CDR present in RX
Extended identifier description : 4.5W max. Power consumption, High Power Class (> 3.5 W) enabled
Connector : 0x07 (LC)
Transceiver codes : 0x80 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Transceiver type : 100G Ethernet: 100G Base-ER4
Encoding : 0x03 (NRZ)
BR, Nominal : 25500Mbps
Rate identifier : 0x02
Length (SMF,km) : 40km
Length (OM3 50um) : 0m
Length (OM2 50um) : 0m
Length (OM1 62.5um) : 0m
Length (Copper or Active cable) : 0m
Transmitter technology : 0x60 (1310 nm EML)
Laser wavelength : 1310.000nm
Laser wavelength tolerance : 1.045nm
Vendor name : WAVESPLITTER
Vendor OUI : 00:0f:0e
Vendor PN : WST-QS28-ER4L-C
Vendor rev : 40
Vendor SN : C920E80002
Date code : 221024
Revision Compliance : SFF-8636 Rev 2.5/2.6/2.7
Module temperature : 31.99 degrees C / 89.58 degrees F
Module voltage : 3.1661 V
Alarm/warning flags implemented : Yes
Laser tx bias current (Channel 1) : 58.114 mA
Laser tx bias current (Channel 2) : 57.790 mA
Laser tx bias current (Channel 3) : 57.790 mA
Laser tx bias current (Channel 4) : 58.438 mA
Transmit avg optical power (Channel 1) : 1.7210 mW / 2.36 dBm
Transmit avg optical power (Channel 2) : 2.0457 mW / 3.11 dBm
Transmit avg optical power (Channel 3) : 2.2409 mW / 3.50 dBm
Transmit avg optical power (Channel 4) : 1.6778 mW / 2.25 dBm
Rcvr signal avg optical power(Channel 1) : 0.0565 mW / -12.48 dBm
Rcvr signal avg optical power(Channel 2) : 0.0846 mW / -10.73 dBm
Rcvr signal avg optical power(Channel 3) : 0.0710 mW / -11.49 dBm
Rcvr signal avg optical power(Channel 4) : 0.0789 mW / -11.03 dBm
Laser bias current high alarm (Chan 1) : Off
Laser bias current low alarm (Chan 1) : Off
Laser bias current high warning (Chan 1) : Off
Laser bias current low warning (Chan 1) : Off
Laser bias current high alarm (Chan 2) : Off
Laser bias current low alarm (Chan 2) : Off
Laser bias current high warning (Chan 2) : Off
Laser bias current low warning (Chan 2) : Off
Laser bias current high alarm (Chan 3) : Off
Laser bias current low alarm (Chan 3) : Off
Laser bias current high warning (Chan 3) : Off
Laser bias current low warning (Chan 3) : Off
Laser bias current high alarm (Chan 4) : Off
Laser bias current low alarm (Chan 4) : Off
Laser bias current high warning (Chan 4) : Off
Laser bias current low warning (Chan 4) : Off
Module temperature high alarm : Off
Module temperature low alarm : Off
Module temperature high warning : Off
Module temperature low warning : Off
Module voltage high alarm : Off
Module voltage low alarm : Off
Module voltage high warning : Off
Module voltage low warning : Off
Laser tx power high alarm (Channel 1) : Off
Laser tx power low alarm (Channel 1) : Off
Laser tx power high warning (Channel 1) : Off
Laser tx power low warning (Channel 1) : Off
Laser tx power high alarm (Channel 2) : Off
Laser tx power low alarm (Channel 2) : Off
Laser tx power high warning (Channel 2) : Off
Laser tx power low warning (Channel 2) : Off
Laser tx power high alarm (Channel 3) : Off
Laser tx power low alarm (Channel 3) : Off
Laser tx power high warning (Channel 3) : Off
Laser tx power low warning (Channel 3) : Off
Laser tx power high alarm (Channel 4) : Off
Laser tx power low alarm (Channel 4) : Off
Laser tx power high warning (Channel 4) : Off
Laser tx power low warning (Channel 4) : Off
Laser rx power high alarm (Channel 1) : Off
Laser rx power low alarm (Channel 1) : Off
Laser rx power high warning (Channel 1) : Off
Laser rx power low warning (Channel 1) : Off
Laser rx power high alarm (Channel 2) : Off
Laser rx power low alarm (Channel 2) : Off
Laser rx power high warning (Channel 2) : Off
Laser rx power low warning (Channel 2) : Off
Laser rx power high alarm (Channel 3) : Off
Laser rx power low alarm (Channel 3) : Off
Laser rx power high warning (Channel 3) : Off
Laser rx power low warning (Channel 3) : Off
Laser rx power high alarm (Channel 4) : Off
Laser rx power low alarm (Channel 4) : Off
Laser rx power high warning (Channel 4) : Off
Laser rx power low warning (Channel 4) : Off
Laser bias current high alarm threshold : 110.000 mA
Laser bias current low alarm threshold : 10.000 mA
Laser bias current high warning threshold : 100.000 mA
Laser bias current low warning threshold : 20.000 mA
Laser output power high alarm threshold : 5.6234 mW / 7.50 dBm
Laser output power low alarm threshold : 0.7244 mW / -1.40 dBm
Laser output power high warning threshold : 4.4668 mW / 6.50 dBm
Laser output power low warning threshold : 1.1482 mW / 0.60 dBm
Module temperature high alarm threshold : 90.00 degrees C / 194.00 degrees F
Module temperature low alarm threshold : -10.00 degrees C / 14.00 degrees F
Module temperature high warning threshold : 85.00 degrees C / 185.00 degrees F
Module temperature low warning threshold : -5.00 degrees C / 23.00 degrees F
Module voltage high alarm threshold : 3.6300 V
Module voltage low alarm threshold : 2.9700 V
Module voltage high warning threshold : 3.4700 V
Module voltage low warning threshold : 3.1300 V
Laser rx power high alarm threshold : 0.5622 mW / -2.50 dBm
Laser rx power low alarm threshold : 0.0049 mW / -23.10 dBm
Laser rx power high warning threshold : 0.4466 mW / -3.50 dBm
Laser rx power low warning threshold : 0.0062 mW / -22.08 dBm
ethtool -m enps01np0
slx9640# show media int ether 0/28 Interface Ethernet 0/28 Identifier 17 QSFP28 Connector 7 LC Transceiver 0000000000000003 100_GB/s Long_dist Name lw Encoding 3 NRZ Baud Rate 255 (units 100 megabaud) Length 9u 10 (units km) Length E-50u 0 (units 2 meters) Length 50u 0 (units 1 meters) Length 62.5u 0 (units 1 meters) Length Cu 0 (units 1 meter) Vendor Name BROCADE Vendor OUI 00:05:1e Vendor PN 57-1000334-01 (100GE QSFP-28 LR4 (10km; 4.5w)) Vendor Rev A Wavelength 26200(units 0.05 nm) Options 030f Loss_of_Sig BR Max 255 BR Min 218 Serial No YDK116390000218 Date Code 160919 Optical Monitor Yes Temperature 35 Centigrade Voltage 3299.1 (mVolts) Current (Agg) 301.024 (mAmps) TX Power (Agg) 6744.5 (uWatts) / 8.289 (dBm) RX Power (Agg) 2324.6 (uWatts) / 3.663 (dBm) Channel [0]: Current 72.492 (mAmps) TX Power 1932.6 (uWatts) / 2.861 (dBm) RX Power 666.8 (uWatts) / -1.760 (dBm) Channel [1]: Current 93.720 (mAmps) TX Power 1156.6 (uWatts) / 0.632 (dBm) RX Power 661.5 (uWatts) / -1.795 (dBm) Channel [2]: Current 60.582 (mAmps) TX Power 1818.0 (uWatts) / 2.596 (dBm) RX Power 207.7 (uWatts) / -6.826 (dBm) Channel [3]: Current 74.230 (mAmps) TX Power 1837.3 (uWatts) / 2.642 (dBm) RX Power 788.6 (uWatts) / -1.031 (dBm)
# sudo i2cdump -f -y 1 0x50
No size specified (using byte-data access)
0 1 2 3 4 5 6 7 8 9 a b c d e f 0123456789abcdef
00: 03 04 07 10 00 00 00 00 00 00 00 06 67 00 00 00 ????.......?g...
10: 08 03 00 1e 46 49 4e 49 53 41 52 20 43 4f 52 50 ??.?FINISAR CORP
20: 2e 20 20 20 00 00 90 65 46 54 4c 58 38 35 37 31 . ..?eFTLX8571
30: 44 33 42 43 4c 20 20 20 41 20 20 20 03 52 00 48 D3BCL A ?R.H
40: 00 1a 00 00 41 4e 4b 31 44 33 48 20 20 20 20 20 .?..ANK1D3H
50: 20 20 20 20 31 32 31 31 31 37 20 20 68 f0 03 cc 121117 h???
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
nv show int xx pluggable
ethtool
l1-show
PS C:\Users\s> mst status MST devices: ------------ mt4115_pciconf0 PS C:\Users\s> mlxlink -d mt4115_pciconf0 -m Operational Info ---------------- State : Polling Physical state : ETH_AN_FSM_XMIT_DISABLE Speed : N/A Width : N/A FEC : N/A Loopback Mode : No Loopback Auto Negotiation : ON Supported Info -------------- Enabled Link Speed : 0x00000001 (SDR) Supported Cable Speed : 0x00000001 (SDR) Troubleshooting Info -------------------- Status Opcode : 0 Group Opcode : N/A Recommendation : No issue was observed Tool Information ---------------- Firmware Version : 12.28.2006 MFT Version : mft 4.27.0-83 Module Info ----------- Identifier : QSFP28 Compliance : N/A Cable Technology : 1310 nm DFB Cable Type : Optical Module (separated) OUI : Other Vendor Name : FINISARCORP. Vendor Part Number : FTLC1151RDPL2 Vendor Serial Number : U24A99K Rev : A0 Wavelength [nm] : 1302 Transfer Distance [m] : 0 Attenuation (5g,7g,12g) [dB] : N/A FW Version : N/A Digital Diagnostic Monitoring : Yes Power Class : 3.5 W max CDR RX : ON,ON,ON,ON CDR TX : ON,ON,ON,ON LOS Alarm : N/A Temperature [C] : 31 [10..65] Voltage [mV] : 3267 [2970..3630] Bias Current [mA] : 0,0,0,0 [25..55] Rx Power Current [dBm] : -40,-40,-40,-40 [-14..6] Tx Power Current [dBm] : -40,-40,-40,2 [-8..8]
> show transceiver-detail ethernet2/23
> debug system interface-xcvr-info log-1